Elegant and bright spaces

white marble tiles maxi size – polished and honed finish – sizes 91,4×45,7 – th. 1 cm

The new white marble tiles, maxi size, can satisfy a variety of visual needs and be used to create stylish, sophisticated surfaces. Unfailingly original, highly versatile and long-lasting, they can add an exquisite touch not only to private homes but also to hotels, offices and public places, especially where limited weights and thicknesses are required.

WHITE MARBLES

• Bianco Carrara
• Bianco Gioia
• Calacatta
• Bianco Statuario
• Bianco Statuarietto

ADVANTAGES

Thin marble tiles, 1 cm (3/8”) thick, polished, bevelled edges. These elements are expressly engineered to obtain these advantages:

• Rational utilization due to the modular format
• Simple setting
• Ready to use, because pre polished
• Reduced weight (28 kg/mq)

PACKAGING

Goods are packed in card-board boxes:

• 1 box 91,4×45,7 cm contains 4 tiles – 1,67 mq (17,97 sq ft)

FLOOR LAYING

Adhesive consumption: Kg 3 – 4 per sq mt

A) On flat concrete or on existing floor:

1st PHASE

Adhesive buttering with teethed spatula (lactic addition could be advisable)

Morble tiles installation (three rows by time)

2nd PHASE (one day after)

Joint grouting by applying o colored grout all over the surface by means of a rubbered spatula

Cleaning up after one hour with sawdust end rags. After one day floor is dried off end ready

B) On uneavy floor

1st PHASE

Preparing the sand and cement subbase

Sprayng over cement powder, wetting with water end applying the tiles over, by pressing them so to obtain a perfect adherence

2nd PHASE (two days after)

Joint grouting by applying a colored grout all over the surface

Cleaning up after one hour with sawdust end rags. After one day, floor is dried off end ready

WALL LAYING

1st PHASE

• Adhesive buttering by means of a teethed spatula (lactic addition advisable for exterior veneers)
• Marble tiles installation (three rows by time)

2nd PHASE (one day after)

• Joint grouting by applying a colored grout by mean of a softener
• Cleaning up after one hour, with rags

MARBLE TILES CHARACTERISTICS

• The variations in colour and veins are typical features of natural products and are also recognisable within the same colour groups.
• You are advised to present the marble tiles dry, choosing from multiple boxes and waiting for them to dry naturally (to overcome any differences in colour due to humidity in the boxes) and then arrange the layout to obtain the best and most pleasant composition, according to the natural features of the product.
• The screed must be perfectly dry to avoid any stains or streaks appearing, which were not present in the marble, but caused by the humidity of the surface underneath, and to avoid possible detachment of small marble chips and surface mastic.
• The screed must also be perfectly smooth to facilitate flatness of the surfaces, reducing unevenness between the marble tiles to a minimum.
• Laying should only be carried out using specific adhesives for marble, in particular chosen based on the types of two-component adhesives suitable for the type of marble to lay GRANIRAPID (Mapei) or similar, white and light-coloured marble in general KERALASTIC (Mapei) or similar, for green marble, Asiago marble, black marble etc.
• Once the material is laid, it should be thoroughly washed to remove all residues of adhesive or other contaminants from its surface. Do not use acids of any sort since even if diluted they tend to alter the appearance of the materials. You should use neutral detergents like FILACLEANER or similar, diluted to a 1:20 ratio. Apply a stain protectant, such as FILA MP90 (natural effect) or FILA STONE PLUS (restoring effect) or similar, when the floor is dry. Rub it into the surface to help it penetrate; then wipe off any excess. Finish the treatment with wax, such as FILA MATT (matt effect) or FILA SATIN (semigloss effect) or similar.